Drive A error 驱动器A错误
System halt 系统挂起
Keyboard controller error 键盘控制器错误
Keyboard error or no keyboard present 键盘错误或者键盘不存在
BIOS ROM checksum error BIOS　ROM校验错误
Single hardisk cable fail 当硬盘使用Cable选项时硬盘安装位置不正确
FDD Controller Failure BIOS 软盘控制器错误
HDD Controller Failure BIOS 硬盘控制器错误
Driver Error 驱动器错误
存储器' target='_blank'>Cache Memory Bad, Do not Enable Cache 高速缓存Cache损坏，不能使用
Error: Unable to control A20 line 错误提示：不能使用A20地址控制线
Memory write/Read failure 内存读写失败
Memory allocation error 内存定位错误
CMOS Battery state Low CMOS没电了
Keyboard interface error 键盘接口错误
Hard disk drive failure 加载硬盘失败
Hard disk not present 硬盘不存在

Floppy disk(s) fail (40) 软盘驱动器加载失败，一般是数据线插反，电源线没有插接，CMOS内部软驱设置错误
CMOS checksum error-efaults loaded. CMOS校验错误，装入缺省(默认)设置
Detecting floppy drive A media... 检测软驱A的格式
Drive media is : 1.44Mb1.2Mb 720Kb 360K 驱动器格式是1.44Mb、12Mb、720kb、360kb的一种
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER 磁盘引导失败，插入系统盘后按任意键继续

Invalid partition table 无效的分区表
Error loading operating system 不能装入引导系统
Missing operating system 系统引导文件丢失
Invalid system disk 无效的系统盘
Disk I/O error, Replace the disk and press any key. 磁盘I/O错误，替换磁盘后按任意键，当C盘系统文件丢失或被破坏时出现。
Invalid Media Type reaching Drive C: 无效的Ｃ盘媒体格式说明。也就是C盘没有格式化或者是其他操作系统的磁盘格式如NTFS

Invalid Boot Diskette Boot Failure 无效的启动盘，启动失败
Insert diskette for drive and press any key when ready 插入磁盘到驱动器中后按任意键

Your program caused a divide overflow error If the problem persists, contact your program vendor程序导致溢出错误。 Windows has disabled direct disk access to protect your long filenames Windows不能直接访问受保护的长文件名

The system has been halted. Press Ctrl+Alt+Del to restart your computer 系统挂起，按Ctrl+Alt+Del重新启动你的计算机

You started your computer with a version of MS-DOS incompatible with this version of Windows. Insert a Startup diskette matching this version of Windows and then restart 你启动的MS-DOS版本与Windows版本不兼容，请插入与Windows版本匹配的系统盘后再重启

This version of Windows requires a 386 or better processor 该Windows版本需要386以后的CPU支持
A20 hardware error. Contact technical support to identify the problem 地址线A20错误。联系技术支持来识别该问题
Starting Windows 98... 正在启动Windows 98……
Windows 98 is now starting your MS-DOS-based program Windows 98正在启动基于MS-DOS的程序
Windows 98 is now restarting... Windows 98正在重新启动
Press Esc now to cancel MS-DOS mode and restart Windows 98... 按Esc退出MS-DOS 模式，重新启动Windows 98…
There is an unrecognized command in your CONFIG.SYS file 在你的CONFIG.SYS文件中有不可识别的命令

The following command in your CONFIG.SYS file is incorrect: 在你的CONFIG.SYS有下列错误命令
The sector size specified in this file is too large: 该文件中指定的扇区太大
The following file is missing or corrupted: WIN.COM COMMAND.COM 下列文件丢失或被破坏：WIN.COM和COMMAND.COM
There is an invalid country code or code page in your CONFIG.SYS file 在你的CONFIG.SYS里有一个无效的国家代码
There is an error in the COUNTRY command in your CONFIG.SYS file 在你的CONFIG.SYS里有一个错误的设置国家命令
There is not enough memory for the COUNTRY.SYS file 没有足够的内存来加载COUNTRY.SYS文件
Remove some drivers from your CONFIG.SYS file, and then try again 请从CONFIG.SYS文件中删除部分驱动程序，然后再试
Remove some drivers, and then try again 去除一些驱动程序然后再试。驱动程序是指在CONFIG.SYS中使用device或devicehigh命令加载的程序文件
Remove some disk drivers from your CONFIG.SYS file, and then try again 从你的(CONFIG.SYS)移去部分程序，然后再试
The configuration specified in your CONFIG.SYS file is too large for memory 调整你的CONFIG.SYS文件以获得足够大的内存
You have too many block devices specified in your CONFIG.SYS file 调整你的CONFIG.SYS文件以获得block devices
The STACKS setting(s) in your CONFIG.SYS file are incorrect 在你的CONFIG.SYS中堆栈设置不正确
Default stack settings will be used instead 缺省的堆栈设置将被替代使用
There is an error in your CONFIG.SYS file on line XX 在你的CONFIG.SYS里XX行错误
Warning: Logical drives past Z exist and will be ignored 警告：逻辑驱动器Z已经存在，将被忽略
Type the name of the Command Interpreter (e.g., C:\WINDOWS\COMMAND.COM) Press any key to continue… 请输入命令解释器的文件名(如：C:\WIN DOWS\COMMAND.COM)后，按任意键继续
Windows is bypassing your startup files Minimal network support will be loaded if available Windows正在跳过你的启动文件。如果网络可用，最小网络支持将被加载